Iron Fence Installation in Hollywood, FL - Timeline, Cost & What to Expect
An iron fence installation in Hollywood typically runs $3,500-$9,000 for a standard residential property and takes 3-5 days from permit approval to final walkthrough. Most homeowners in Hollywood’s 33027 and 33029 ZIP codes schedule this work as part of a full exterior upgrade or as a standalone security and curb-appeal project. Call (844) 665-0162 for a free on-site estimate and written breakdown.
How We Build an Iron Fence - Stage by Stage
Day one is layout and demo. We mark the fence line with stakes and string, then remove whatever’s in the way: old chain link, rotted wood posts, or crumbling concrete footings from a previous install. In Hollywood’s older east-side neighborhoods near Stirling Road and Federal Highway, we often hit original 1960s footings that have to be cut out with a hydraulic breaker. That adds a half-day but prevents the new posts from drifting. You’ll decide on exact gate placement and walk-through width before we dig.
Day two is excavation and rough inspection. We auger post holes 30-36 inches deep depending on panel height, set gravel base, and place posts in concrete. Broward County requires a footing inspection before backfill on any fence over 6 feet, so we schedule the inspector for late afternoon. If you’re in a gated community like Emerald Hills or Hollywood Lakes, we’ll need your HOA’s approved finish sample on-site for the inspector to verify.
Day three is panel hanging and welding. We bolt or weld panels to posts depending on the design - welded frames with cast-iron pickets for traditional looks, or modular steel panels with concealed fasteners for cleaner sight lines. This is when you see the real rhythm of the job. A 150-linear-foot run takes most of a day. We grind welds flush and apply a rust-inhibiting primer coat before you make your final walk-through.
Day four is finish coating and hardware. We apply two coats of Sherwin-Williams DTM acrylic enamel or a powder-coat finish if you spec’d it. Gates get hung, self-closing hinges adjusted, and latch hardware set to your preferred height. If you’ve asked for automation, we mount the opener and run low-voltage conduit to your power source.
Day five is final inspection and detail cleanup. We pull permit final, touch up any scuffs, and walk the line with you. The concrete footings cure for 72 hours; we ask you to keep gates unlatched and vehicles off the gravel for that window. Total elapsed time from your signed contract: 2-3 weeks including permit submission and Broward’s review queue.
The Iron Fence Options You’ll Actually Choose Between
- Wrought iron vs. tubular steel: True wrought iron is hand-forged, heavier, and priced at a premium - think $45-$75 per linear foot installed. Tubular steel is fabricated from hollow bar stock, lighter, and runs $25-$40 per foot. For Hollywood’s salt-air environment, we spec steel with a hot-dip galvanized undercoat either way; raw iron without it will surface-rust within two years near the Intracoastal.
- Picket style and spacing: Four-inch spacing meets pool-code in Broward without extra mesh. Two-inch spacing looks more formal but costs 15-20% more in material. Spear-top pickets add security; flat-top or loop-top read friendlier for front-yard applications.
- Panel height: 4 feet for decorative front-yard work, 6 feet for side and rear privacy, 8 feet for security perimeters. Each 2-foot jump adds roughly $8-$12 per linear foot. Hollywood’s flat topography means wind load increases with height; 8-foot panels need deeper footings and thicker post stock.
- Finish type: Spray-applied enamel is standard and field-repairable. Powder coat is harder and more uniform but requires shop application and touch-up kits for future dings. For coastal properties east of the Intracoastal, we lean toward powder coat for its salt-spray resistance.
- Gate configuration: Single swing up to 5 feet wide, double swing beyond that, or sliding track for driveways with limited clearance. Automated openers add $1,200-$2,800 depending on voltage, battery backup, and access control. Many of our seasonal residents in Hollywood opt for keypad and remote packages so guests and property managers can enter without a physical key.
What Iron Fence Costs in Hollywood, FL
Most residential iron fence projects in Hollywood fall between $3,500 and $9,000. Here’s what moves you within that range:
| Factor | Low-end driver | High-end driver |
|---|---|---|
| Linear footage | Under 100 ft | 200+ ft with multiple gates |
| Existing conditions | Clear sod, no demo | Old concrete removal, tree roots, utility locates |
| Material grade | Standard tubular steel, sprayed finish | Heavy-wall steel or wrought iron, powder coat |
| Site access | Open yard, no obstructions | Tight side yards, pool equipment to work around |
| Permit scope | Standard fence permit only | HVHZ engineering review, HOA variance, DEP coastal setback |
A written estimate from us includes layout, materials, labor, permit fees, and one site-prep day. It does not include tree removal, irrigation relocation, or electrical service upgrades for gate openers - those get line-itemed separately if needed. Call (844) 665-0162 for an exact quote; estimates are free.
What Hollywood Homes Specifically Do to This Job
Hollywood’s split personality as a city changes how we approach iron fence work. East of I-95, in the 33020 and 33021 ZIPs, we’re often mounting to 1960s concrete block walls or drilling into aging CBS construction where the original stucco is brittle. We use wedge anchors with epoxy backup, not standard lead shields, and we expect to patch stucco where posts penetrate. The salt air off Hollywood Beach - we’re talking about properties along Surf Road and the Ocean Drive corridor - forces us to spec 316-grade stainless fasteners and thicker zinc coatings than we’d use inland. That barrier island strip also sits under Florida’s Coastal Construction Control Line, so any fence with a footing within 50 feet of the mean high-tide line triggers a DEP permit layer that mainland Broward projects never see.
Then there’s the HVHZ reality. Hollywood sits in Florida’s High Velocity Hurricane Zone alongside Miami-Dade, and that means the fasteners, post bases, and gate hardware we use must carry a Miami-Dade Notice of Acceptance. Contractors coming up from Palm Beach County or over from Central Florida get caught at the Broward permit desk when their standard Florida Product Approval doesn’t include the HVHZ listing. We’ve seen projects stall three weeks while replacement hardware gets sourced. We spec HVHZ-listed from the start.
West Hollywood and the 33027-33029 planned communities - think West Lake Village and Pembroke Pines-adjacent tracts - present cleaner sites but stricter HOA design covenants. Many of those associations require black or dark bronze finishes only, limit height to 4 feet in front setbacks, and mandate concealed fasteners. We pull the CC&Rs before we quote so your design board submission goes through clean the first time.
Serving Hollywood, FL - Our Local Coverage Area
We’re based in the Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked - Iron Fence in Hollywood
From permit approval to final walkthrough, most iron fence projects take 3-5 working days. Add 7-10 business days upfront for Broward County permit review, or longer if your property is east of the Intracoastal and needs DEP coastal clearance. Call (844) 665-0162 and we’ll check current permit queue times.
Yes, any fence over 6 feet or any fence with concrete footings requires a Broward County building permit, plus an HOA approval letter if you’re in a deed-restricted community. We handle the application, the HVHZ hardware documentation, and the inspections as part of our project fee. Call (844) 665-0162 for an exact quote - estimates are free.
Usually, yes. We locate utilities and irrigation before we dig, then adjust the fence line in 6-inch increments to miss buried lines. If your pool equipment pad sits exactly on the property line, we may need to shift a post or build a short jog - we’ll flag that during layout on day one so you can decide before we concrete. Call (844) 665-0162 to schedule a site walk.
Aluminum won’t rust but it’s lighter and flexes more in high wind; iron is stronger and takes impact better but needs proper coating to survive the salt air. For Hollywood’s HVHZ wind loads and coastal exposure, we typically spec heavy-gauge steel with hot-dip galvanizing and powder coat - the strength of iron with corrosion protection that matches aluminum’s lifespan. Call (844) 665-0162 and we’ll walk you through the trade-offs for your specific site.
Our workmanship warranty covers structural integrity and gate operation for the period specified in your written contract. Material warranties vary by finish type: spray enamel carries a 3-5 year coating warranty from the manufacturer, while powder coat typically runs 10-15 years against chalking and fading. Hardware warranties depend on the specific hinge and latch manufacturer. We name every warranty term in your estimate so there’s no ambiguity. Call (844) 665-0162 for details.
Get Your Iron Fence Estimate in Hollywood
We’ll walk your property, measure the line, check for buried utilities and HOA requirements, and deliver a written estimate with material specs and a clear timeline. No deposit required to schedule. Call (844) 665-0162 or reach out through our Hollywood service page to get started.
Written by Raymond Estevez, Owner at Groundwork Construction Co., serving Hollywood and Broward County homeowners since our founding.