How Much Does Tub-to-Shower Conversion Cost in Broadview Park, FL?
A tub-to-shower conversion in Broadview Park typically runs $3,500-$10,000, with most projects we quote falling in the $5,500-$7,500 range for a standard 60-inch alcove swap with updated plumbing and a mid-grade surround. Most jobs take 4-7 working days from demo to final inspection, though Broward County’s permit timeline can add 2-3 weeks upfront. Call (844) 665-0162 and we’ll walk through your exact layout - estimates are free, and we pull the county permit for you.
How We Handle Tub-to-Shower Conversion - Start to Finish
We’ve done enough of these in Broadview Park and nearby unincorporated pockets of Broward County to know where the delays hide. Here’s how we stage the work so you’re not living in construction longer than necessary.
Stage 1: Site measure and scope lock (Day 0-1)
We photograph the existing tub, measure rough openings, and test water pressure and drain flow. This is when you decide: keep the 60-inch width or bump to a 48-inch shower with a linen closet? Curbed or curbless? Wall surround material - acrylic, fiberglass, or tiled? We mark up the layout together, then submit to Broward County’s ePlan portal. That submission happens before we touch a tool.
Stage 2: Demo and rough-in expose (Days 2-3)
We remove the tub, surround, and any water-damaged subfloor or studs. In Broadview Park’s 1950s-1970s CBS ranches, we almost always find galvanized drain lines, shallow vent stacks, or electrical outlets that sit too low for modern GFCI placement. If we’re relocating the drain from center to linear, or moving a valve wall, this is when that work happens. We also test for asbestos in older mastic - common in pre-1980 builds here.
Stage 3: Plumbing and electrical rough (Days 4-5)
New pressure-balanced or thermostatic valve body goes in. We upsize to 3/4-inch feeds when possible - the water pressure in older Broadview Park mains can be inconsistent, and a larger line helps. Drain gets reconfigured for the new shower base slope. Electrical gets brought to code: dedicated GFCI circuit, proper exhaust fan venting (not just recirculating), and any lighting upgrades. County rough inspection gets scheduled here.
Stage 4: Surround and fixture install (Days 6-8)
Shower base gets set and leveled. Wall panels or tile go up. We pay attention to the “wet wall” - in block construction, furring strips and moisture barriers matter more than in frame homes. Niche placement, grab bar blocking, and bench framing all happen now. Final fixture selection (head, handheld, trim) gets installed and pressure-tested.
Stage 5: Finish, cleanup, and final inspection (Days 9-10)
Caulk, seal, hardware alignment, and a full water test. We walk you through operation and cleaning for your specific surround material. Then we call Broward County for the final inspection. If you’ve got an HOA in Broadview Park, we provide the certificate of completion for their records.
The Options You’ll Choose Between for Your Tub-to-Shower Conversion
Every choice below affects price, maintenance, and how the shower feels daily. We don’t push one over another - we explain the trade-off, then you decide.
- Shower base: Acrylic vs. tile vs. solid surface. Acrylic bases ($400-$900) drop in fast, have built-in slopes, and clean easily - but the color palette is limited and they can flex underfoot. Tiled bases with a membrane ($1,200-$2,500) look custom and last decades, yet need re-grouting every few years in Florida’s hard water. Solid surface like Swanstone ($800-$1,600) splits the difference: seamless, repairable, more colors than acrylic.
- Wall surround: Fiberglass surround vs. tile vs. slab panels. Three-piece fiberglass ($600-$1,200) is done in a day and costs least, but the seams collect mildew and it looks rental-grade. Ceramic or porcelain tile ($2,000-$5,000+) gives you design control and longevity, yet demands more cleaning. Large-format slab panels like cultured marble or quartz ($1,800-$3,500) install with minimal grout lines - a smart middle ground for busy households.
- Plumbing fixtures: Builder grade vs. pressure-balanced vs. thermostatic. Basic single-handle valves ($150-$300) work fine until someone flushes a toilet. Pressure-balanced ($250-$450) prevents scalding - worth it in homes with kids or older adults. Thermostatic ($500-$1,200+) holds exact temperature and supports multiple outlets (rain head plus handheld). We stock Moen, Delta, and Kohler lines across all three tiers.
- Glass enclosure: Framed vs. semi-frameless vs. frameless. Framed sliders ($400-$800) seal tight and cost least, but the metal channels corrode in Florida humidity. Semi-frameless ($700-$1,400) drops the top rail. True frameless ($1,200-$2,500+) needs thicker glass and precise walls, yet it’s what most homeowners picture when they say “spa shower.” In Broadview Park’s older block homes, wall plumbness determines whether frameless is realistic without major reframing.
- Drain position: Keep center drain vs. relocate to linear or offset. Keeping the existing drain location saves $800-$1,500 in concrete cutting and repiping. Moving to a linear drain along the threshold ($1,200-$2,000 extra) enables curbless entry - a genuine accessibility upgrade, though it requires floor recessing that’s tricky in slab-on-grade construction common here.
What Tub-to-Shower Conversion Costs in Broadview Park, FL
| Project Scope | Typical Range |
|---|---|
| Basic tub-to-shower swap, same layout, acrylic surround | $3,500-$5,500 |
| Mid-grade conversion, tile surround, new valve, framed glass | $5,500-$7,500 |
| Full reconfiguration, curbless entry, frameless glass, upscale fixtures | $8,000-$10,000 |
Five factors move you up or down that range:
1. Existing condition of walls and floor. We see a lot of water-damaged greenboard and termite-compromised furring in pre-1980 Broadview Park baths. Replacing subfloor, sistering studs, or treating mold adds $500-$2,000.
2. Plumbing relocation. Moving the drain or valve wall in a concrete slab home means cutting block, running new lines, and patching - typically $800-$2,500 depending on distance and access.
3. Material grade. The spread between an acrylic three-piece surround and a full tile job with niche and bench can be $3,000+ in materials alone.
4. Electrical and ventilation upgrades. Older homes here often need new GFCI circuits, exhaust fans ducted to exterior, and sometimes panel work if you’re adding a steam generator or heated floor. Budget $400-$1,500.
5. Permit scope and inspection cycles. Broward County charges permit fees based on project valuation - typically $200-$500 for this work. If rough inspection fails due to code issues in older wiring or plumbing, each re-inspection adds time, not always money, but time has cost if you’re down to one bathroom.
Our written estimates include demo, disposal, all materials specified, labor, permit pulling, and final inspection coordination. What’s typically separate: bathroom vanity replacement, floor tile outside the wet area, and any Bathroom Remodeling in Broadview Park scope beyond the shower enclosure itself.
What Broadview Park Homes Specifically Do to This Job
Broadview Park’s unincorporated status means every tub-to-shower conversion permit routes through the Broward County Building Division’s ePlan system - not Plantation’s or Lauderhill’s municipal desks. We’ve watched out-of-area contractors stumble on this, submitting to the wrong portal and losing two weeks. Our Bathroom Remodeling crew handles the county workflow weekly, so we know which inspector covers the ZIP 33317 area and what they flag on older homes.
The housing stock matters too. Most baths we work in here sit inside 1950s-1970s concrete block ranches with original galvanized drains, shallow vent stacks, and electrical outlets that predate GFCI requirements. When we open a wall, we often find the tub was wet-set directly on slab with no moisture barrier behind the surround - explaining the musty smell homeowners mention. The block walls themselves are sound, but furring strips are sometimes irregular or insect-damaged, so we don’t assume we can hang a heavy frameless door without verifying anchor points.
Because these homes predate the post-Hurricane Andrew Florida Building Code, county inspectors treat any plumbing or electrical modification as a trigger for current-code compliance. That means your new shower gets anti-scald protection, proper venting, and GFCI whether the rest of the house has it or not. It’s non-negotiable, and we price for it upfront rather than surprising you mid-project.
Seasonal timing also shapes schedules here. After named storms, Broward County’s inspection backlog can stretch from days to weeks. We plan around it, but if you’re targeting a start date, call early - especially heading into hurricane season.
Homeowners in Broadview Park often pair interior updates with exterior work. If your roof or windows are original to a 1960s build, you may want to talk through Metal Roofing in Broadview Park or Tile Roofing in Broadview Park while we’re already coordinating county permits. One contractor, every phase - less scheduling chaos for you.
Serving Broadview Park, FL - Our Local Coverage Area
We’re based in the Broadview Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked - Tub-to-Shower Conversion in Broadview Park
Active construction is 4-7 working days, but budget 3-5 weeks total including Broward County permit review and inspection scheduling. Call (844) 665-0162 and we’ll check current county turnaround times.
Yes - because Broadview Park is unincorporated Broward County, any plumbing or electrical modification requires a county building permit. We pull it through the ePlan portal and schedule inspections for you.
Often yes, if you’re keeping the 60-inch alcove width and center drain. We simply swap the tub for a shower base and update the valve. Keeping existing plumbing locations saves roughly $800-$1,500 and avoids concrete cutting in your slab floor.
An acrylic shower base and three-piece fiberglass surround with your existing drain and valve locations runs about $3,500-$4,500 in Broadview Park. The trade-off is shorter lifespan and limited style options. Call (844) 665-0162 and we’ll quote both budget and upgrade paths so you can compare.
We warranty our workmanship for one year. Manufacturer warranties vary by product: acrylic bases typically carry 10-30 years, tile installations rely on our waterproofing warranty, and fixtures range from lifetime (Moen, Delta) to 5-10 years for entry lines. We document all warranties in your closeout packet.
Get Your Free Tub-to-Shower Conversion Estimate in Broadview Park
Call (844) 665-0162 or fill out our contact form. We’ll schedule a 45-minute site visit in Broadview Park, measure your space, test your existing plumbing, and email a detailed estimate within 24 hours. No deposit to schedule, no pressure to decide on the spot - just specific numbers for your specific bathroom.
Written by Raymond Estevez, Owner at Groundwork Construction Co., serving Broadview Park and Broward County homeowners since our founding.