Vanities, Tile & Fixtures in Dania - Same-Day Service, Done Right the First Time

Vanities, Tile & Fixtures in Dania, FL - What’s Included, How Long It Takes, and What It Costs

Vanities, tile, and fixtures in Dania typically run $800-$3,000 for the vanity installation portion alone, with full bathroom tile and fixture packages pushing toward the higher end of the $9,000-$28,000 bathroom remodel range depending on material grade and whether plumbing stays put. Most vanity, tile, and fixture swaps we handle in Dania finish in 3-5 working days if we’re not relocating drains or supply lines. Call (844) 665-0162 and we’ll walk through your layout and give you a written, itemized estimate - no charge for the site visit.

Call (844) 665-0162

This isn’t a full bathroom overhaul. It’s the surgical replacement of the three surfaces and systems that age fastest in a Florida bathroom: the vanity cabinet and top, the wall and floor tile, and the faucet, shower valve, and lighting package. Homeowners in Dania call us for this when the cabinet doors are swelling from humidity, the grout is stained beyond cleaning, or the chrome fixtures have corroded from salt air. We treat it as a standalone job with its own permit scope, or as part of a full Bathroom Remodeling in Dania if you’re addressing the shower or tub at the same time.

How we handle vanities, tile, and fixtures - the actual process

Day one is demo and rough inspection. We pull the old vanity, mirror, and any wall-mounted cabinets, then strip tile down to the substrate. In Dania’s 1940s-1960s stock, we often find plaster or early cement board that won’t support modern large-format tile without replacement. Our crew tests for moisture intrusion behind the vanity - a common issue where original block walls have settled and cracked. If the wall is wet, we stop and show you before continuing. The rough plumbing inspection happens same-day or next morning if we’re moving supply or drain locations.

Days two and three are substrate and layout. We install cement board or waterproof membrane (we use Schluter or equivalent systems rated for wet areas), then lay out the tile pattern with you physically present. This is where you decide: stacked or offset, accent strip or no, grout color. For Dania’s coastal humidity, we spec epoxy grout in shower-adjacent walls - standard sanded grout elsewhere. The vanity rough opening gets leveled; older Dania homes often have floors that settled ¼ inch or more across a 5-foot wall.

Day four is tile set and fixture rough. We set floor tile first, then wall tile, working out cuts so the visible edges hit the vanity or a planned trim piece. If you’ve chosen a floating vanity, we add blocking to the studs now - never trust drywall anchors for 80+ pounds of cabinet and quartz. The plumber roughs in valves for the new faucet and any shower or tub spout if that’s in scope. Electrical runs for sconces or LED mirrors happen here too.

Day five is grout, vanity hang, and finish plumbing. We grout, seal, then install the vanity, top, sink, faucet, and mirror. Final electrical connections for fixtures. We run water, check for leaks, caulk all transitions, and clean out. You walk it with the lead carpenter. If we’re part of a larger project, this is where our bathroom remodeling crew hands off to the shower or tub team.

The homeowner makes three binding decisions: tile and grout selection (before demo), vanity size and configuration (before rough plumbing), and fixture finish (before final install). Change any of these mid-stream and we add 2-3 days minimum. We’re happy to do it - we just want you to know the real cost of the pivot.

The material and layout choices you’ll actually decide between

• Floating vs. furniture-style vanity: Floating opens floor space and reads modern, but requires solid wall blocking and hides less of Dania’s often-uneven floors. Furniture-style on legs covers more, stores more, and costs 15-25% less for equivalent cabinet quality. In flood-prone AE zones near the Intracoastal, floating vanities reduce water contact if minor flooding occurs.
• Quartz, cultured marble, or solid surface top: Quartz (Cambria, Silestone, Caesarstone) resists etching and comes in 2 cm or 3 cm; 3 cm needs no build-up but adds $400-$800. Cultured marble is budget-friendly but scratches and yellows over time in sunlit Dania bathrooms. Solid surface (Corian-type) repairs seamlessly but lacks the depth of quartz.
• Ceramic, porcelain, or natural stone tile: Porcelain absorbs less than 0.5% - critical for Dania’s humidity and any bathroom without continuous exhaust. Ceramic costs 30-40% less but is more porous. Natural stone (travertine, marble) demands sealing every 12-18 months in salt-air environments; most Dania homeowners who choose it do so for a single accent wall, not the full bath.
• Large-format vs. standard tile: 12×24 or 24×24 porcelain has fewer grout lines (less mildew habitat) but requires flatter walls - often meaning more prep in older Dania homes. Standard 4×16 or 6×6 tile forgives wavy studs but needs more grout maintenance.
• Fixture finish and valve grade: Brushed nickel and matte black hide water spots better than polished chrome in hard-water Broward County. For shower valves, we spec pressure-balanced as minimum; thermostatic adds $200-$400 but holds temperature when someone flushes elsewhere in the house - worth it in older Dania homes with ½-inch supply lines.

What vanities, tile, and fixtures cost in Dania, FL

Vanity, tile, and fixture work in Dania falls between $800 and $3,000 for a straightforward vanity replacement, and $4,500-$12,000 when you’re retiling walls and floors with mid-grade materials and new fixtures throughout. The full bathroom remodel range of $9,000-$28,000 applies if we’re also addressing the wet area (shower or tub surround).

Five variables push you to the high or low end. First: keeping plumbing in place saves $800-$1,500 versus relocating drains or supplies through concrete slab or block walls. Second: material grade - a KraftMaid or Wellborn vanity with quartz top runs 2-3× a big-box cabinet with cultured marble. Third: wall condition - tile over intact drywall is cheaper than replacing water-damaged substrate in older Dania homes. Fourth: tile size and pattern - herringbone or diagonal cuts add 20-30% labor. Fifth: permit scope - a simple vanity swap may not require permitting, but any wall tile in a wet area triggers Broward County inspection and adds $200-$400 in fees and scheduling.

Our written estimates include demo, disposal, materials, labor, permit fees if applicable, and final cleaning. They do not include your tile or fixture selections if you purchase them separately (we’re happy to source through our trade accounts for better pricing), nor any hidden damage we discover after demo - we document and pause, never surprise-bill.

What Dania homes specifically do to this job

Dania’s housing stock changes how we bid and build vanities, tile, and fixtures. As one of Broward’s oldest cities, much of what’s standing went up between the 1940s and 1960s - concrete block or wood-frame construction that predates modern waterproofing and often carries original galvanized supply lines. We replace those with PEX or copper before hanging a new vanity; it’s not optional if we find them, and it adds half a day.

The salt-air factor is real. Homes east of Federal Highway, especially near Dania Beach Boulevard and the Intracoastal, see faster corrosion on exposed brass and chrome. We spec stainless or PVD-coated fixtures for those properties, and we check the wall cavity for rusted anchor bolts when we demo. It’s not alarmist - it’s what the 33004 ZIP demands after thirty years of onshore flow.

Permitting in Dania runs through Broward County’s unified system, but with a local twist: any project that might require scaffolding above certain heights or rooftop mechanical work triggers FAA Part 77 review because of Fort Lauderdale-Hollywood International’s approach corridors. For a standard vanity, tile, and fixture job inside the envelope, this rarely applies. But if your remodel is Dania property near the airport flight path and you’re also having roofing or exterior work done - say, you’re pairing this with Tile Roofing in Dania or Specialty Roofing in Dania - we coordinate the FAA filing as a standard pre-construction step. Out-of-town contractors often miss this. We don’t.

HOA layers add complexity in Dania’s beachside condos and some of the historic districts near Frost Park. Material color palettes, contractor insurance requirements, and work-hour restrictions are common. We pull those documents before we quote, not after.

Frequently asked - vanities, tile, and fixtures in Dania

Ready to talk through your Dania bathroom?

Call (844) 665-0162 for a free on-site estimate. Raymond Estevez or a lead carpenter will walk your bathroom, measure rough-ins, check wall and floor condition, and email you an itemized quote within 24 hours. No deposit required to schedule, and we only book what our crew can build well.

Written by Raymond Estevez, Owner at Groundwork Construction Co., serving Dania and Broward County homeowners with full-scope residential construction since establishing our Fort Lauderdale base.