PGT Bathroom Remodeling in South Florida, FL

PGT Bathroom Remodeling: The South Florida Owner’s Guide

PGT bathroom remodeling in South Florida typically runs $9,000-$28,000 for a full renovation with PGT windows or doors integrated into the space, and we can usually get your project scoped and scheduled within 48 hours. Most homeowners come to us after noticing moisture intrusion around an existing PGT unit, hardware corrosion from salt air, or frame swelling that signals the window or door system is no longer sealing properly against our wet climate. If you’re seeing fog between glass panes, warped sashes, or hardware that grinds instead of glides, the unit has likely reached the end of its serviceable life in South Florida’s conditions.

Call (844) 665-0162

Which PGT Models This Applies To

We work with the full PGT residential line, including WinGuard impact-rated vinyl and aluminum windows, EnergyVue vinyl frames, and PGT’s architectural aluminum series commonly found in South Florida bathrooms for their corrosion resistance. The critical compatibility gotcha is the fastening pattern: WinGuard aluminum frames use a 4-inch jamb screw spacing that differs from standard vinyl window rough openings, so retrofitting without adjusting the surround framing often leaves gaps that leak in our driving rains. Check the etched mark in the glass corner or the AAMA label on the frame edge for the series code (WGA for WinGuard aluminum, WGV for vinyl, ENV for EnergyVue).

OEM PGT sashes and hardware are our default for impact-rated units because aftermarket equivalents rarely carry the same HVHZ (High Velocity Hurricane Zone) certification required from Miami-Dade north through Broward and Palm Beach counties. For non-impact interior bathroom windows, we sometimes spec quality aftermarket frames from our KraftMaid-adjacent supply chain when the homeowner wants to match cabinetry finishes exactly. We stock common PGT sash balances, weep-hole covers, and corrosion-resistant hardware kits on our trucks for same-day stabilization.

Signs Your PGT Bathroom Remodeling Is Failing

• Fog or condensation between panes. This means the insulated glass unit (IGU) seal has failed, which happens faster in South Florida bathrooms where steam from showers accelerates seal degradation. The inert gas escapes, moisture enters, and the thermal performance drops to nearly single-pane levels.
• Frame swelling or vinyl warping. PGT vinyl frames can absorb moisture if the weep holes clog with salt residue, a common issue within two miles of the coast in Fort Lauderdale, Hollywood, and Pompano Beach. The frame distorts and the sash no longer seats squarely.
• Hardware grinding or latch misalignment. Salt air corrodes zinc-plated hardware faster than inland climates; once the cam lock or tilt latch seizes, forcing it bends the internal mechanism and damages the keeper.
• Water staining on drywall below or beside the unit. This usually traces to failed perimeter sealant or a compromised sill pan, not the window itself, but the fix requires removing the PGT unit to address the rough opening properly.
• Draft or temperature stratification near the window. In South Florida, this often means the constant-force balance has weakened in the humid bathroom environment, letting the sash drop slightly open even when “closed.”

Replacement Cost & What’s Included

What drives the range: unit size (PGT makes bathroom windows from 24×36 up to 60×48), impact rating required by your municipality, and whether the rough opening needs reframing for moisture damage. Our quotes itemize the PGT unit cost, labor for removal and installation, permit handling, and finish carpentry to match your existing trim. We pull permits through the proper South Florida municipal channels and coordinate inspections so you’re not chasing paperwork.

DIY or Call Us?

Homeowners can safely check the PGT label location (glass corner etch, frame edge sticker, or between the sash and frame on tilt-wash units) and measure the daylight opening to confirm sizing. You can also clear weep holes with a pipe cleaner and verify that exterior sealant isn’t cracked or separated.

Where DIY goes wrong: removing an impact-rated PGT unit without supporting the header properly can destabilize the wall above, and reinstalling without proper sill pan flashing directs water into the stud bay. In South Florida, that moisture turns to mold fast. We also see homeowners use standard silicone instead of structural glazing tape or approved sealants, which voids the impact certification. If your bathroom PGT unit is failing, call us at (844) 665-0162 and we’ll scope it honestly. Do it right the first time or you’ll do it twice - and the second time always costs more.

FAQs