CGI Bathroom Remodeling in South Florida, FL

CGI Bathroom Remodeling: The South Florida Owner’s Guide

CGI bathroom remodeling in South Florida typically runs $9,000-$28,000 for a full renovation with CGI windows and doors integrated into the design, and we can usually start the assessment within 48 hours. Most homeowners discover their CGI products need attention when they notice water intrusion around window frames after heavy rains, or when they’re updating a bathroom and realize the existing CGI impact-rated windows don’t match the new layout. In South Florida’s climate, the salt air and hurricane exposure mean CGI products need proper sealing and integration with moisture barriers - something we account for in every bathroom remodel we take on.

Call (844) 665-0162

Which CGI Models This Applies To

CGI’s product lines for bathroom applications in South Florida fall into three main categories: the Estate Series (aluminum impact windows with narrow frames), the Sentinel Series (vinyl impact-rated options), and the commercial-grade Targa and WinGuard lines used in higher-end residential work. The critical compatibility gotcha is frame depth - Estate Series frames run 2-5/8 inches deep, while Sentinel vinyl frames are 3-1/4 inches, and swapping one for the other without adjusting the rough opening throws off tile transitions and waterproofing membranes. We always verify the etched model number in the glass corner and the white spec label on the frame edge before ordering. For bathroom remodels, we typically see the Estate 200 and 400 series in coastal homes from Boca Raton down through Key Largo, where the narrow sightlines matter in smaller baths. OEM CGI parts maintain the original impact certification; aftermarket equivalents exist for hardware and weatherstripping but won’t carry the Miami-Dade NOA number that your building inspector may ask for if permits get pulled.

Signs Your CGI Bathroom Remodeling Is Failing

• Water staining on drywall below or beside the window. In South Florida, this usually means the CGI frame-to-wall seal has degraded, or the weep holes are clogged with salt residue. The water follows the path of least resistance and shows up inches from the actual leak.
• Condensation between panes on double-glazed CGI units. The insulated glass seal has failed. In our humidity, this happens faster than manufacturer estimates suggest - we’ve replaced CGI IGUs in Hallandale Beach bathrooms that failed at year eight despite a ten-year glass warranty.
• Difficulty latching or the sash won’t stay open. The balance system or hinge hardware is corroding from salt air exposure. CGI’s aluminum hardware holds up better than most, but the stainless steel screws in coastal installs can gall after five to seven years.
• Visible frame corrosion or pitting. This is more common on non-CGI windows, but we’ve seen it where CGI frames were installed without proper isolation from dissimilar metals - like copper flashing or galvanized fasteners that set up galvanic reaction.
• Whistling or air infiltration during storms. The compression seal around the sash has hardened. In a bathroom, this also means you’re losing conditioned air and pulling humid attic air through wall cavities.

Replacement Cost & What’s Included

A full bathroom remodel with CGI window integration in South Florida runs $9,000-$28,000 depending on scope. Here’s how that breaks:

The wide range on full remodels reflects whether we’re moving plumbing, the grade of tile and fixtures selected, and how many CGI openings need replacement versus reuse. We itemize every line - no “allowances” that balloon later. Our labor warranty covers installation workmanship; CGI’s own warranty covers the product. We’re an independent service provider, not affiliated with CGI, so we advocate for you if a warranty claim is needed.

DIY or Call Us?

There’s a clear line here. Homeowners can safely check weep holes for debris, verify that caulk joints are intact, and confirm the model numbers for ordering parts. What you shouldn’t touch: removing a CGI impact-rated window from a bathroom rough opening disturbs the moisture barrier, and re-establishing that seal properly requires integrating with the tile waterproofing system - get it wrong and you’re growing mold in the stud bay within a season. The aluminum frames aren’t heavy, but the precision of the install determines whether the window drains water out or traps it in. We’ve been called to redo DIY CGI installs in Coral Gables where the homeowner saved $400 on labor and spent $3,200 on drywall, tile, and frame replacement six months later. Do it right the first time or you’ll do it twice - and the second time always costs more. Call (844) 665-0162 and we’ll scope it honestly.

FAQs