Cabinets & Countertops in Lake Worth - Same-Day Service, Done Right the First Time

What Cabinets & Countertops Installation Costs and Involves in Lake Worth

Cabinets & countertops replacement in Lake Worth typically runs $6,000-$19,500 for a standard kitchen, with most projects finishing in 5-10 business days from template to final seal. You’ll choose your materials and layout early, we handle permitting and templating, and the actual install usually takes 2-3 days. Call (844) 665-0162 for a free on-site estimate with measured pricing.

Call (844) 665-0162

How We Handle Cabinets & Countertops From First Measurement to Final Caulk

We’ve refined this into five clear stages so you know what’s happening and when you need to make decisions.

Stage 1: Site measure and layout lock (Day 1)

We arrive with laser measures and a checklist. This is where you finalize cabinet box dimensions, countertop depth and overhang, and whether you’re keeping your existing footprint or moving appliances. Most Lake Worth kitchens we measure fall between 90 and 140 square feet of cabinetry run. You’ll decide on door style, finish, and hardware by the end of this visit. We photograph plumbing and electrical positions, note any soffits or bulkheads that affect cabinet height, and flag whether your existing flooring extends under the cabinets or butts to them. That detail alone changes demo scope and cost by $400-$800.

Stage 2: Material order and permit pull (Days 2-14)

Cabinet lead times vary. Stock maple or white shaker from KraftMaid ships in 10-14 days. Semi-custom painted finishes from Wellborn run 4-6 weeks. Countertops template only after cabinets are set, so we order material now but hold fabrication until post-install. If you’re in eastern Lake Worth Beach (33460-33462), we pull permits through the city; west of Military Trail in 33449 or 33467, it’s Palm Beach County. Same job, two different submittal portals, and county typically adds 3-5 business days to initial review. We handle both, but you’ll see the permit authority on your estimate so there’s no confusion.

Stage 3: Demo and cabinet install (Days 15-17)

We protect flooring, disconnect plumbing and electrical, and remove old cabinets. If your home was built before 1994 in the older blocks near Dixie Highway, we inspect for embedded anchors and blocking. The new boxes go in level and screwed to studs, not just walls. This stage takes one day for a straight replacement, two if we’re modifying a peninsula to an island or adjusting cabinet heights to eliminate a soffit. You don’t need to be home, but we call before we cap plumbing so you can confirm faucet and disposal placement.

Stage 4: Countertop template and fabrication (Days 18-25)

We template with digital probes for quartz or granite, or physical sticks for solid surface. Cambria and Silestone fabricate in 5-7 business days; Caesarstone can stretch to 10 during peak season. We specify edge profile now (eased, beveled, ogee, or waterfall) and confirm sink and cooktop cutouts. This is your last chance to change anything without material charges. We schedule installation only after you’ve approved the digital layout.

Stage 5: Countertop set, plumbing reconnect, and final inspection (Days 26-28)

The slabs arrive on A-frames. We seam at sink cutouts where possible, seal with color-matched epoxy, and reconnect your faucet, disposal, and dishwasher. County or city inspector verifies electrical and plumbing rough before we call it complete. Most of our Lake Worth cabinets & countertops projects pass first inspection; when they don’t, it’s usually a missing GFCI or an unbonded disposal that we fix same day.

The Material Choices That Actually Change How Your Kitchen Works

• Stock vs. semi-custom vs. custom cabinets: Stock cabinets (KraftMaid’s standard lines) run $120-$200 per linear foot, ship fast, and offer limited sizes. Semi-custom (Wellborn’s Designer Series) adds 30-50% cost but lets you adjust depth, add glass inserts, or match a specific paint code. Custom is rarely necessary unless you’re working around structural quirks in older Lake Worth homes with non-standard ceiling heights or angled walls.
• Frameless European vs. face-frame construction: Frameless gives you 10-15% more interior cabinet space and full-overlay doors with hidden hinges. Face-frame is stiffer, more forgiving on uneven walls, and easier to repair if a hinge strips out. In 1940s-1970s block homes with settled walls, we often recommend face-frame for durability.
• Quartz vs. granite vs. solid surface: Engineered quartz (Cambria, Silestone, Caesarstone) is non-porous, consistent in pattern, and needs no sealing. Granite varies slab to slab, handles heat better, but requires annual sealing. Solid surface (Corian-type) is repairable and seamless but scratches easier and can’t take a hot pan. For rental properties or heavy-use kitchens in Lake Worth’s coastal humidity, we steer toward quartz.
• Undermount vs. drop-in sink: Undermount with quartz or granite gives you a clean wipe into the sink. Drop-in works with any countertop and costs less to replace later. If you’re keeping a cast-iron sink from a previous remodel, we need to verify it fits the new cabinet base and countertop cutout before we order.
• Standard overlay vs. full overlay vs. inset doors: Standard overlay shows 1/2-inch of face frame, full overlay covers it completely, inset sits flush inside the frame. Inset requires precise humidity-stable construction and adds 20-30% to cabinet cost. In Lake Worth’s seasonal humidity swings, we only spec inset with engineered wood cores, never solid hardwood frames.

What Cabinets & Countertops Costs in Lake Worth, FL

Five variables push you toward the high or low end of that combined range:

Existing condition. Cabinets sitting on tile that runs wall-to-wall require floor repair or replacement after removal. If your subfloor is plywood over concrete slab (common in pre-1994 CBS homes), we may need to grind anchors flush. That adds $300-$600.

Plumbing and electrical relocation. Keeping your sink, range, and dishwasher in place saves $1,500-$3,000. Moving any of them requires new supply lines, drain routing, and often a permit revision.

Material grade. Entry-level quartz starts around $55 per square foot installed. Cambria’s designer lines or thick 3cm slabs with waterfall edges run $110-$140. Cabinet grade differences are equally wide.

Permit scope. Straight cabinet swap with no electrical or plumbing changes may not require permitting in unincorporated Palm Beach County. Add under-cabinet lighting, a disposal circuit, or gas cooktop relocation, and you’re in full permit territory with inspections adding 2-3 days to the schedule.

HOA architectural review. In western Lake Worth communities like those along Lake Worth Road or in the 33467 corridors, exterior-facing kitchen windows or changes visible from common areas trigger board approval before permit filing. That adds 2-4 weeks upfront.

Our written estimates include demo, disposal, cabinets, countertops, hardware, installation, plumbing reconnect, and permit fees. They don’t include appliance replacement, flooring repair beyond the cabinet footprint, or structural modifications like removing a load-bearing wall. If you’re considering a full Kitchen Remodeling in Lake Worth that includes those elements, we’ll scope that separately so you can phase the work.

What Lake Worth Homes Specifically Do to This Job

The split jurisdiction here shapes every project timeline. A cabinet job on Lucerne Avenue in 33460 pulls through Lake Worth Beach’s permit office with its own fee schedule and inspection calendar; the same scope on Hypoluxo Road in 33467 goes to Palm Beach County. We’ve worked both enough to know that county inspectors typically want to see electrical and plumbing rough before cabinets are fully secured, while city inspectors often allow a single final walkthrough. We sequence accordingly, but it means we can’t promise identical timelines for two kitchens three miles apart.

The housing stock pushes material choices too. Those 1940s-1970s concrete block homes east of Dixie Highway have walls that aren’t always plumb. Face-frame cabinets forgive that; frameless European boxes need shimming and sometimes furring strips that eat into your budget. We’ve also learned to check for original jalousie windows above sinks. Replacing them with fixed glass or impact-rated casements is a separate job, but the rough opening dimensions affect your backsplash height and upper cabinet depth.

Coastal humidity is real here. Solid wood cabinet doors without engineered cores will move seasonally. We spec plywood box construction with MDF center panels for painted finishes, and we avoid particleboard entirely in ground-floor kitchens near the lagoon where flooding history exists. For Lake Worth homeowners considering a broader renovation, we often discuss whether this cabinet project is standalone or part of a larger scope. Many clients pair kitchen updates with Walk-In Showers & Shower Remodeling in Lake Worth or a Tub-to-Shower Conversion in Lake Worth to consolidate scheduling and minimize repeat disruption.

Our Kitchen Remodeling crew also sees recurring issues in the western HOA communities: architectural review boards want finish samples and sometimes manufacturer spec sheets before they’ll sign off. We keep digital folders of KraftMaid and Wellborn samples specifically for this purpose, and we submit on your behalf if you prefer.

Frequently Asked - Cabinets & Countertops in Lake Worth

Get a Measured Estimate for Your Lake Worth Kitchen

We’ll come to your home, measure precisely, and build a line-item estimate for cabinets and countertops that accounts for your specific layout, material preferences, and whether you’re in Lake Worth Beach or unincorporated Palm Beach County. No deposit required to schedule. Call (844) 665-0162 or request your free estimate online. Most Lake Worth appointments are available within 48 hours.

Written by Raymond Estevez, Owner at Groundwork Construction Co., serving Lake Worth and South Florida homeowners since 2018.